WAGNER Paint Crew Uživatelský manuál

Français - p. 25Español - p. 49Owner’s ManualContents Before You Start 2 Important Safety Information 4 What’s in the Box 5 Assemble Your Wagn

GOOD JOB!Hold the Spray Gun LevelBADStart3. Practice SprayingWhat you’ll need•Scrap material/cardboardGOOD JOB!Practice on a piece of scrap material/

Start strokeEnd strokePull triggerRelease triggerMove steadily!GOOD JOB! BADSpray TechniqueSpray PatternGOOD SPRAY PATTERN BAD SPRAY PATTERN: TAILINGG

If material isn’t flowing properly after clearing these things see additional instructions in the Fix Spraying Problems sectionPage 22Common Solutions

LOCKlO3Note: If spray tip is difcult to rotate relieve pressure by turning PRIME/SPRAY knob to PRIME and squeeze trigger while pointing at scrap mate

HANDLEHANDLEStartIMPORTANT: Never clean lter by poking with sharp object.Perform Pressure Relief ProcedurePage 74. Remove inlet lter from hopper3. E

Start1Clean the Spray Gun FilterWhat you’ll need•Wrench•Warm, soapy water for latex material•Mineral spirits for oil based materials•Replacement s

HOPPER LID5. If your break is more than an hour slowly pour ½ cup of water of paint in hopper. This helps prevent paint from drying and causing possib

4. Steps for Getting Material to Flow (page 9)3. If water was added during shut down stir water into material2. Remove spray gun from plastic bag or f

lOSQUEEZETURNONHANDLEHANDLElOOFFFlush Material From Sprayer12. Turn knob to PRIME and squeeze trigger until pressure is relieved. Release trigger, loc

lOlOONOFF2-3 MINUTES3. Remove inlet lter and clean with appropriate cleaning solution. Replace inlet lter in hopper9. Hold material return tube ove

Important Safety InformationRead all safety information before operating the equipment. Save these instructionsto PRIME to relieve the pressure. Refer

HOUSEHOLDOILHOUSEHOLDOILStartClean Spray Gun ComponentsWhat you’ll need• Soft bristled brush• Light household oil• Warm, soapy water if using latex ma

lOONOFF5 SECONDSHOUSEHOLDOILHOUSEHOLDOILlOStart1Long Term Storage2. Remove inlet lter4. Cover outlet valve with a rag. Turn power ON. Let run for 5

Before servicing, always release system pressure by following Pressure Relief Procedure (page 7).Problem A: The sprayer does not startCause Solution1.

Problem D: The PRIME/SPRAY knob is set to SPRAY and there is flow through the material return tubeCause Solution1. The PRIME/SPRAY valve is dirty or wo

Inlet fittingO-ringInlet fittingO-ringInletfittingO-ringInletfittingInletvalveInletvalveO-ring2. Remove inlet lter from bottom of hopper4. Inspect th

Español74Français74English744851327661234569Spray Gun • Pistolet • PistolaSprayer • Pulvérisateur • Rociador Item Article ArticuloPart No. No de piéce

Warranty • Garantie • GarantíaEspañol75FrançaisEnglishLimited WarrantyAIRLESS PAINT SPRAY EQUIPMENT This product, manufactured by Wagner Spray Tech Co

Grounded outletGrounded pinCover for grounded outlet box• This product may be used only with water-based materials or materials with a minimum ash po

SPRAYPRIMEOlSpray HoseTriggerTrigger LockSpray Tip AssemblySpray Hose FittingThe Spray GunHopper LidSpray Hose OutletON/OFF SwitchHopperMaterial Retur

3. On each side of the handle install bolt and tighten wing nut over lock washer2. Insert handleStart1Start1Assemble Your Wagner Paint CrewWhat you’ll

SPRAYPRIMEOlProper Use and FunctionsSpecicationsWeight . . . . . . . . . . . . . . . . . . .25 lbsCapacity . . . . . . . . . . . . . . . . . .2 gall

lOStartImportant Safety WarningBe careful when handling the spray gun so you don’t accidently spray yourself. The high pressure paint stream could pi

lOlOONOFFHOPPER LIDStart1. Load MaterialWhat you’ll need•The material you plan to spray• Extension cord•Waste container2. Push tab on lter twice to

SQUEEZElOONLOCKWhat you’ll need•Scrap material/cardboard•Drop cloths to protect oors and furnishings from overspraySpecial NoteDon’t let the hopper